WhatsApp Support

Hello! I'm here to help with the 2-Month Internship Program for Mechanical & Civil Engineering Students.
Ask me about the sessions, projects, or registration.
Chat on WhatsApp
🔥 Limited Seats Available

2-MONTH INTERNSHIP PROGRAM

FOR MECHANICAL & CIVIL ENGINEERING STUDENTS

LEARN · BUILD · INNOVATE · SUCCEED

Build practical, industry-oriented skills through hands-on training and real-time IoT & Embedded Systems projects.

2
Months
30
Sessions
4
Real-Time Projects
100%
Hands-on Training
Hands-on Training Real-Time Projects Industry Ready
Apply for Internship View Sessions

Embedded Systems

Fundamentals of microcontrollers and embedded programming

IoT Projects

Build real-time IoT applications with ESP32 and sensors

Industry Focused

Practical skills that companies are looking for

Hands-on Training

Learn by building real-world projects

IoT Sensors & Technologies

Work with industry-relevant sensors and technologies

Soil Moisture Sensor

Measure soil moisture levels for smart irrigation

DHT22 Sensor

Temperature & Humidity monitoring

Water Pump Control

Automated water pump management

Water Level Sensor

Real-time water level monitoring

Internship Sessions

30 comprehensive sessions covering Embedded Systems, Arduino, Sensors, Communication Protocols, ESP32, IoT, and Industry Projects

Session 1

Introduction to Embedded Systems

What is an Embedded System, Real-time systems, Architecture, Examples in appliances, automobiles, industrial automation, IoT

🔧 Hands-on: Identify embedded systems in real-world products
Session 2

Microcontroller Fundamentals

Microprocessor vs Microcontroller, Architecture, CPU, ALU, Registers, RAM, ROM, Flash, EEPROM, GPIO, ADC, DAC, Timers, Interrupts

🔧 Hands-on: Arduino UNO board architecture and pin identification
Session 3

Arduino UNO & Development Environment

Arduino UNO overview, ATmega328P, Digital/Analog/PWM/UART/I2C/SPI pins, IDE installation, setup(), loop(), compilation, upload, Serial Monitor

🔧 Hands-on: First LED blinking program
Session 4

Embedded C Programming Fundamentals

Variables, Constants, Data types, Operators, If-else, Switch-case, Loops (for, while, do-while), Functions

🔧 Hands-on: Create different LED blinking patterns
Session 5

Digital Input and Output

Digital signals, GPIO concepts, Input/Output mode, pinMode(), digitalWrite(), digitalRead(), Push button, Pull-up/down resistors

🔧 Hands-on: Push-button-controlled LED system
Session 6

Analog Signals and ADC

Analog vs Digital, ADC, Resolution, Reference voltage, analogRead(), Potentiometer, LDR interfacing, Sensor calibration

🔧 Hands-on: Read potentiometer and LDR values through ADC
Session 7

PWM and Output Control

PWM waveform, Frequency, Duty cycle, LED brightness control, Motor speed control, Servo control basics

🔧 Hands-on: Control LED brightness using PWM
Session 8

Serial Communication and Debugging

UART basics, TX/RX, Baud rate, Serial.begin(), Serial.print(), Serial.println(), Serial Monitor, Debugging

🔧 Hands-on: Real-time sensor data monitoring on Serial Monitor
Session 9

Temperature & Humidity Sensors

DHT22 sensor, Temperature and Humidity measurement, Sensor calibration, Threshold-based control

🔧 Hands-on: Temperature & Humidity monitoring system
Session 10

Soil Moisture Sensor

Soil moisture measurement, Dry and wet soil detection, Sensor calibration, Threshold setting

🔧 Hands-on: Soil moisture monitoring system
Session 11

Water Level Sensor

Water level measurement, Analog and digital sensor outputs, Threshold setting, Alarm system

🔧 Hands-on: Water level monitoring system
Session 12

Water Pump Control & Automation

Relay interfacing, Pump control logic, Automated pump management, Safety features

🔧 Hands-on: Automated water pump control system
Session 13

IR and Ultrasonic Sensors

IR sensor, Object/Obstacle detection, Ultrasonic sensor (HC-SR04), Trigger/Echo pins, Time-of-flight principle, Distance calculation

🔧 Hands-on: Build an obstacle and distance detection system
Session 14

Relay and Load Control

Electromagnetic relay, COM/NO/NC, Relay modules, Electrical isolation, Flyback diode, AC vs DC loads

🔧 Hands-on: Control a load using Arduino and relay
Session 15

LCD and OLED Displays

16×2 LCD, Parallel and I2C LCD, OLED display, Displaying text and sensor readings, Custom characters

🔧 Hands-on: Display live sensor values
Session 16

UART Communication Protocol

Synchronous vs Asynchronous, UART architecture, Baud rate, Start/Data/Parity/Stop bits, Full duplex

🔧 Hands-on: Serial communication between two embedded devices
Session 17

I2C Communication Protocol

Two-wire communication, SDA/SCL, Master/Slave, Device address, Start/Stop conditions, ACK/NACK, Pull-up resistors

🔧 Hands-on: Interface an OLED display or I2C sensor
Session 18

SPI Communication Protocol

Synchronous communication, MOSI/MISO/SCLK/Chip Select, Full-duplex, Multiple slaves, UART vs I2C vs SPI comparison

🔧 Hands-on: SPI device communication demonstration
Session 19

Introduction to ESP32

ESP32 architecture, Dual-core, GPIO, ADC, DAC, PWM, Timers, Interrupts, Wi-Fi, Bluetooth, ESP32 vs Arduino UNO

🔧 Hands-on: ESP32 LED blinking and GPIO programming
Session 20

ESP32 Wi-Fi Connectivity

Wi-Fi fundamentals, SSID, Password, IP address, Station/AP mode, Connecting to Wi-Fi, Reconnection techniques

🔧 Hands-on: Connect ESP32 to Wi-Fi and display its IP address
Session 21

IoT Architecture and Fundamentals

IoT device, Sensors, Actuators, Edge devices, Gateway, Network, Cloud, Dashboard, Device/Communication/Processing/Application layers

🔧 Hands-on: Design a Sensor → ESP32 → Wi-Fi → Dashboard architecture
Session 22

ESP32 Local Web Server

Web server, Client-Server architecture, HTTP, GET/POST, HTML fundamentals, Control buttons, Reading GPIO states

🔧 Hands-on: Control a relay from a mobile browser
Session 23

Real-Time IoT Dashboard

Dashboard concept, Sensor data acquisition, HTML/CSS/JavaScript, AJAX, Auto-refresh, Gauges, Charts, Status indicators

🔧 Hands-on: Build a live monitoring dashboard
Session 24

MQTT and Cloud IoT Basics

MQTT broker, Publisher/Subscriber, Topic, Message, QoS levels, Retained messages, Cloud IoT basics

🔧 Hands-on: Publish and monitor real-time sensor data
Session 25

Integration of Sensors & Actuators

Combining multiple sensors, Data fusion, Actuator control, System integration

🔧 Hands-on: Multi-sensor integration system
Sessions 26–30

Industry Projects & Final Demonstration

Boiler Safety & Security System, Temperature-Based Automatic Fan Control System, Earthquake & Structural Crack Detection System, Smart Irrigation System

🔧 Hands-on: Hardware integration, Firmware development, IoT dashboard, Testing, Project documentation, Final presentation, Technical viva

Hands-on IoT Projects

Build practical, industry-oriented skills through hands-on training and real-time IoT projects

1. Boiler Safety & Security System

  • Temperature and pressure monitoring
  • Real-time safety alerts
  • Automatic shutdown system

2. Temperature-Based Automatic Fan Control System

  • DHT22 temperature sensing
  • Automatic fan speed control
  • Energy efficient operation

3. Earthquake & Structural Crack Detection System

  • Vibration sensor monitoring
  • Structural crack detection
  • Real-time alert system

4. Smart Irrigation System

  • Soil moisture monitoring
  • Automatic water pump control
  • Real-time dashboard

What You Will Learn

Comprehensive training covering everything from fundamentals to real-world applications

ESP32 Controller

Master ESP32 programming and IoT applications

IoT Projects & Applications

Build real-world IoT solutions for industry

ESP32 & Arduino Programming

Write efficient code for embedded systems

Sensors & Actuators

Work with soil moisture, DHT22, water level sensors

Real-Time Monitoring & Control

Dashboards, data visualization, and automation

Hands-on Project Development

Complete project lifecycle from design to deployment

Program Fee
₹ 4,000
Inclusive of training, materials, and certificate

📌 Send me a message on WhatsApp if you are interested

📞 95059 73075

WhatsApp Us Apply Now Call Now